Breville is a registered trademark of Breville Holdings Pty. Limited
ABN 98 000 092 928
Breville Customer Care Centre
✉
Locked Bag 2000
Botany NSW 2019
Australia
Customer Service
(02) 9384 9601
Ph: 1300 139 798
¤
Fax
Email Customer Service
Breville Customer Service Centre
Private Bag 94411
Greenmount
✉
Auckland, New Zealand
Customer Service
0800 288 513
Ph: 09 271 3980
¤
Fax
Email Customer Service
PRINTED ON
RECYCLED PAPER
© Copyright. Breville Holdings Pty. Limited 2004
INSTRUCTIONS FOR USE
MODEL URN6/URN10
Due to continual improvements in design or otherwise, the product you
purchase may differ slightly from the one illustrated in this booklet.
Model URN6/URN10
Issue 2/00
OPERATING YOUR BREVILLE URN
OPERATING YOUR BREVILLE URN (CONTINUED)
BEFORE FIRST USE
☛
☛
It is recommended that before the first use,
the Urn is filled to the maximum level, boiled
and water discarded.
NOTE!
NOTE!
1. Firstly fully unwind power cord from base.
2. Place the Urn on a dry level surface and
position the drip tray at the front of the
Urn (tilt the Urn back and slide the drip
tray under to secure in place fig 1).
4. After filling the Urn, ensure that the lid is
replaced and locked into position.
5. Plug the power cord into a 230/240V
power outlet and switch on. The red ‘on’
light will illuminate.
6. Turn the variable heat control to ‘Hi’ for
fast boiling (fig 3). The heating light will
remain on.
Fig 4
When the unit has boiled, select the
desired setting from ‘Low’ to 7 to
maintain temperature. The heating light
will illuminate on and off maintaining the
temperature selected.
Fig 1
3. To fill with water, turn the locking lid anti-
clockwise and remove (fig 2). Use a
smaller container to fill the Urn between
the minimum and maximum marks. Too
little water will result in the Urn switching
off before the water has boiled.
Fig 5
8. After use, switch the appliance to off,
switch the power off at the power outlet
and then remove the plug when the
appliance is not being used and before
cleaning.
Fig 3
7. To pour hot water, place a cup in the drip
tray and push the non-drip tap down
(fig 4). For continuos pouring, lift the tap
in the vertical position (fig 5).
Fig 6
Lock
Unlock
Fig 2
4
5
SAFETY BOIL DRY PROTECTION
CARE AND CLEANING
The Urn is fitted with a safety device which
protects against overheating should the
appliance be operated with insufficient water
or has boiled dry. If this occurs, the Urn will
stop heating. Both the red and orange lights
will turn off.
Always switch the appliance to off, switch
the power off at the power outlet and then
remove the plug before cleaning. Never
immerse the Urn controls or cord in water,
or allow moisture to come in contact with
these parts.
Switch the appliance to off, switch the
power off at the power outlet and allow the
Urn to cool. Press the safety reset button
under the base before refilling (fig 7). The
safety device will then be reset and the Urn
is ready for use.
REMOVAL OF MINERAL DEPOSITS.
Mineral deposits in tap water may cause the
Urn interior to discolour. This may be
removed by using a commercial kettle
descaler which is available from most
leading supermarkets, departments and
hardware stores.
Fig 7
TO CLEAN THE POLISHED
EXTERIOR.
The stainless steel surface may be wiped
over with a damp cloth and polished with a
soft dry cloth.
☛
NOTE!
6
7
|